Pantone 2016 Spin Swirl Cold Process Soap (Two Ways!

• Oils & Vinegars

  • 18 oz Canola oil
  • 1 oz Castor oil
  • 9 oz Coconut oil
  • 1/2 oz Cotton fragrance oil, Crisp
  • 2 1/2 oz Grass fragrance oil, Sweet
  • 9 oz Palm oil
  • 6 3/4 oz Rice bran oil

• Dairy

  • 1 1/3 oz Avocado butter

• Liquids

  • 14 3/4 oz Distilled water

• Other

  • Activated Charcoal
  • 9 Bar birchwood mold
  • Bright Blue Jean Colorant
  • Fired Up Fuchsia Colorant
  • Orchid Mica
  • Silicone Liner for 9 Bar Mold
  • 6.1 oz. Sodium Hydroxide Lye
  • Titanium Dioxide Pigment

Found on soapqueen.com

Description

Ingredients

• 9 Bar Birchwood Mold
• Silicone Liner for 9 Bar Mold
• Optional: 10″ Silicone Loaf Mold
• 1.4 oz. Avocado Butter
• 18 oz. Canola Oil
• .9 oz. Castor Oil
• 9 oz. Coconut Oil
• 9 oz. Palm Oil
• 6.8 oz. Rice Bran Oil
• 6.1 oz. Sodium Hydroxide Lye
• 14.8 oz. Distilled Water
• 2.5 oz. Sweet Grass Fragrance Oil
• .5 oz. Crisp Cotton Fragrance Oil
• Bright Blue Jean Colorant
• Fired Up Fuchsia Colorant
• Titanium Dioxide Pigment
• Orchid Mica
• Activated Charcoal

Directions

• Slowly and carefully add the lye to the water and gently stir until the lye has fully dissolved and the liquid is clear. Set aside to cool.
• Melt and combine the coconut oil, rice bran oil, canola oil, avocado butter, castor oil and palm oils (remember to fully melt then mix your entire container of palm oil before portioning). Once the lye water and the oils have cooled to 130 degrees or below (and are ideally within 10 degrees of each other), add the lye water to the oils and stick blend until a very thin trace. If you’d like a harder bar of soap that releases faster from the mold, you can add sodium lactate to the cooled lye water. Use 1 teaspoon of sodium lactate per pound of oils in the recipe. For this recipe, you’d add about 2.5 teaspoons sodium lactate.
• Be careful to not over emulsify the batter. The soap batter should be very thin and just emulsified. You can always stick blend more later. =) Once the batter has reached a very thin trace, split the batch into four containers. Each container will contain about 500 mL.
• To each container, add the dispersed colorants in the amounts below. Mix in each colorant with a whisk until completely blended.A (White): 1 Tbs. dispersed Titanium DioxideB (Pink): ½ tsp. dispersed Titanium Dioxide + ½ tsp. dispersed Fired Up Fuchsia (Blue): 1 tsp. dispersed Bright Blue Jean Colorant + ½ tsp. dispersed Titanium DioxideD (Purple): ½ tsp. dispersed activated charcoal + 1 tsp. dispersed Orchid Mica
• Add the fragrance oil blend evenly between the four containers (it’s okay to eyeball it!). Use a whisk to thoroughly mix in the fragrance blend. The batter should still be very thin.
• Now it’s time to pour! I like to place my mold on a Lazy Susan table to help spin the soap once I’m done pouring. The order in which you pour the colors into the mold is up to you. I just recommend choosing a color order and sticking to it throughout pouring. I chose to pour two different patterns of colors in each corner of the mold. This is optional. Pour the pink soap into one corner of the mold and count to three during the pour to help pour an even amount.
• In the opposite corner, pour the white soap while counting to three. Then, pour the blue soap onto the pink while counting to three, and the purple soap onto the white while counting to three. At this point, the soap should be nice and fluid. As you layer the colors, it will push the soap towards the center of the mold and fill it up. Work as quickly as possible during this process, as the soap will continue to thicken up with time. Every now and then, give the colors a whisk to help keep them fluid.
• Pour pink soap onto the purple layer while counting to three, then pour white soap onto the blue while counting to three.
• Pour a layer of blue soap onto the pink while counting to three, then pour purple soap onto the white while counting to three. Working quickly, continue the color pattern in each corner of the mold. The two patterns were: pink, blue, white, purple and white, purple, pink and blue. Continue to pour the soap into the corners of the mold. If necessary, whisk the soap to help it stay fluid. As you can see in the bottom right photo below, my soap batter started to get a little bit thick. Once the soap is not “pushing” the layers below towards the center, but is instead piling on the top, it’s time to stop pouring. If you continue to pour the soap at this texture, the soap will not swirl when spun. This is when I decided the soap was too thick to continue with the spin swirl design. If I had continued to pout the thick soap into the mold, the spin swirl effect would not have been achieved.
• Give the mold a few firm taps on the counter to help eliminate air bubbles, and to help the layers of soap settle. Begin to spin the Lazy Susan (if you have one), stopping it quickly to help give the soap movement. You want the centrifugal force created by the spin and stop movement to move the soap in various directions within the mold. Be careful not to spin too hard, or the soap may spill out of the mold!
• I ended up with a decent amount of leftover soap; there was enough to make a whole different project. Because the soap was fairly thick, I knew it would make a great texture for a spoon plop. Grab a large spoon for each color. Spoon the soap into the mold, one color at a time, layering them in three different spots within the mold.
• Continue to plop the soap into the mold, using various sizes of “plops” for interest.
• Once all the soap has been placed into the mold, tap it firmly on the counter to help eliminate bubbles. Insert a chopstick or dowel into the very top of the soap, and drag the chopstick down the length of the mold in an “S” curve.
• Use the chopstick to swirl the top of the soap in an “S” curve down the length of the mold in the opposite direction. Finally, use the chopstick or dowel to swirl the top of the soap in a “loop de loop” pattern down the length of the mold. Don’t worry too much about making this swirl perfect. =)
• Spray the top of the spin swirl soap, and the spoon plop soap with 99% isopropyl alcohol to help prevent soda ash. Cover both soaps to insulate for 24 hours. Allow the soap to stay in the molds for 3-4 days before attempting to remove. You may find that the spin swirl soap needs extra time in the mold, because it was poured at a very thin trace. Cut into bars and allow to cure for 4-6 weeks before use!