Sahara Sunset Cold Process Soap Tutorial

• Produce

  • 1 Tangerine wow! colorant

• Oils & Vinegars

  • 3/4 oz Beau brummel cybilla fragrance oil
  • 3 1/3 oz Canola oil
  • 8 1/2 oz Coconut oil
  • 3 1/3 oz Hazelnut oil
  • 6 3/4 oz Olive oil
  • 1/2 oz Orange peel cybilla fragrance oil
  • 8 1/2 oz Palm oil
  • 2/3 oz Patchouli fragrance oil

• Bread & Baked Goods

  • 1 Tall 12″ silicone loaf mold

• Drinks

  • 1 Fizzy lemonade colorant

• Dairy

  • 1 2/3 oz Avocado butter
  • 1 2/3 Coffee butter

• Beer, Wine & Liquor

  • 1 Merlot sparkle mica

• Liquids

  • 11 1/4 oz Distilled water

• Other

  • Electric Bubblegum Colorant
  • LCP White Melt and Pour Base
  • Black Oxide
  • Shimmer Yellow Color Block
  • Mini Round Silicone Column Mold
  • 4.8 oz. Sodium Hydroxide Lye

Found on soapqueen.com

Description

Ingredients

• Tall 12″ Silicone Loaf Mold
• 1.7 oz. Avocado Butter
• 3.4 oz. Canola Oil
• 8.5 oz. Coconut Oil
• 1.7 Coffee Butter
• 3.4 oz. Hazelnut Oil
• 6.8 oz. Olive Oil
• 8.5 oz. Palm Oil
• 4.8 oz. Sodium Hydroxide Lye
• 11.2 oz. Distilled Water
• .8 oz. Beau Brummel Cybilla Fragrance Oil
• .6 oz. Patchouli Fragrance Oil
• .5 oz. Orange Peel Cybilla Fragrance Oil
• Black Oxide
• Merlot Sparkle Mica
• Fizzy Lemonade Colorant
• Electric Bubblegum Colorant
• Tangerine Wow! Colorant
• Mini Round Silicone Column Mold
• LCP White Melt and Pour Base
• Shimmer Yellow Color Block

Directions

• Chop and melt 6 oz. of the LCP White Melt and Pour Base in the microwave using 10-15 second bursts. Once melted, add shavings of the Shimmer Yellow Color Block and stir until you achieve a bright yellow color. Pour the soap into the mold and allow the soap to fully cool and harden.
• Once hardened, remove from the mold. Cut the mold in half. Then, trim off about ⅓ of the sphere to create a flat surface. You don’t have to cut the mold in half first if you don’t want to, but I found it was easier to cut a flat surface this way =) Set the embeds aside until you’re ready to make the cold process soap.
• Slowly and carefully add the lye to the water and gently stir until the lye has fully dissolved and the liquid is clear. Set aside to cool.
• Combine the coconut oil, olive oil, hazelnut oil, canola oil, palm oil, coffee butter and avocado butter (remember to fully melt then mix your entire container of palm oil before portioning). Once the lye water and the oils have cooled to 130 degrees or below (and are ideally within 10 degrees of each other), add the lye water to the oils and stick blend until you reach a light trace. If you’d like a harder bar of soap that releases faster from the mold, you can add sodium lactate to the cooled lye water. Use 1 teaspoon of sodium lactate per pound of oils in the recipe. For this recipe, you’d add about 3 tsp. sodium lactate.
• Once the soap has reached a light trace, add the fragrance blend to the entire batch and use a whisk to fully mix in.
• Split the soap into four containers, each will hold about 300 mL. You will have about 1 cup left of soap in the large container. To this soap, add ½ tsp. of dispersed black oxide and use a whisk to mix in.
• To the remaining four containers holding 300 mL, add the dispersed colorants in the amounts below. Use a whisk to mix in the colorants completely.Container A (dark red): 1 teaspoon Merlot Sparkle Mica + 1 teaspoon Tangerine Wow! Colorant + .5 teaspoon Electric Bubblegum Colorant + a few drops of Black OxideContainer B (orange): 2.5 teaspoons Tangerine Wow! Colorant +.5 teaspoon Merlot Sparkle MicaContainer C (light orange): 2 teaspoons Tangerine Wow! ColorantContainer D (yellow): 3.5 teaspoons Fizzy Lemonade Colorant + .5 teaspoon Tangerine Wow! Colorant
• Pour the black soap into the mold, and tap down firmly on the counter to get rid of any bubbles. If your soap is still a very thin trace, stick blend for a few seconds to achieve a medium trace before pouring into the mold.
• Place the melt and pour embeds in top of the black soap, slightly to the side of the mold. Press down very gently so the embed sticks, but is not submerged into the black soap.
• Check the texture of the orange, red and yellow soap. You want quite a thick trace. If it is still thin, stick blend each color light to dark for several seconds until thick. Once it is a nice thick trace (the texture of pudding) spoon the deep red soap into the mold. Use a spoon to create slight peaks into the dark red soap, don’t worry about the layer being perfectly even and straight!
• Use a spoon to plop the dark orange soap on top of the red soap down the entire length of the mold. Use the spoon to spread the orange soap evenly throughout the mold and use the spoon to create very slight peaks into the layer.
• Add the light orange soap on top of the dark orange layer down the entire length of the mold, and use the spoon to create slight texture. Don’t worry about the layer being straight and even!
• Finally, spoon the yellow soap onto the light orange soap down the entire length of the mold, Use the spoon to create a nice textured top. Don’t worry about making it perfect!
• Once you’re happy with the texture on top, tap the mold firmly on the counter several times to get rid of any bubbles. Spray with 99% isopropyl alcohol to avoid any soda ash. Continue to spritz the top with alcohol every 15-20 minutes for the first hour. This helps form a barrier on top that prevents pesky soda ash! Allow the soap to sit in the mold for 3-4 days. Unmold, cut and allow to cure for 4-6 weeks. Enjoy!